Iceweasel
Diamond Member
This is just plain silly. You think it's that easy to unsubscribe? The internets is forever! Well, almost. It IS possible but will require some effort on your part:
How To Unsubscribe from a forum
To unsubscribe from this forum you must first purchase a Craft-O-Matic
Adjustable Subscription Cancellation Unit. The unit can be obtained from
most hardware stores and dental clinics. Be sure to obtain the proper
permits to operate the unit from the Nuclear Regulatory Commission and
the Food and Drug Administration in Washington D.C. USA.
Be sure to carefully unpack the kit and place each component in its
accompanying mesh safety bag. Mount the Pershing DF4 mesinator on top of
the perforated Gerring Mach 77 refibulator and attach them using the
eight-millimeter torque fork. Be sure that the refibulator is mounted at
a 66-degree angle and properly dispersed so that it is flush with the
curved section of the Pyrex thistle tube. Place the four sections of the
triangular separation gear into the posture cylinder and lock them into
place using the band-aid adhesive strip. Insert the wiggling pin into
the wobbling hole, making sure that it seated correctly. Place the D
cell battery and the eleven 9 volt batteries in the power chamber.
The device should be calibrated before operation using the optional
digital corkscrew accessory pack prior to operation. Insert the digital
corkscrew through the electronic combustion service chamber using
caution not to touch the reinforced tungsten igniter control module and
quickly turn the inverter drive to 28.6 degrees. Turn the Craft-O-Matic
Adjustable Subscription Cancellation Unit upside down and hit the bottom
plate with a 48-ounce ball-peen hammer while shaking the unit
vigorously. Force open the door to the incineration valve compartment
and set the pressure gauge to 719 psi. Close the door and seal it shut
with duct tape. The unit should now be properly calibrated and ready to
use.
Before activating the Craft-O-Matic Adjustable Subscription Cancellation
Unit, you must first elevate it to a height of 229 feet above sea level
to insure that the unit receives the proper oxygen level and barometric
pressure. Point the aerial to 17 degrees north by northeast to within
the parameters of the Telstar GS-2 weather satellite and apply pressure
to the wing shaft on the southern most section of the modular
accelerator. Using the special ratchet adapter supplied with the unit,
rotate the heater core to the "on" position. The "on" position has been
obtained when the green light begins to flash, signifying that the red
light is about to go off. Once the red light is off, flip the toggle
switch labeled "ON/OFF" to the "ON" position and count to 47 before
logging on to the system.
Logon using your username and password and wait for the prompt. Once
prompted you must check the box with the appropriate action you wish to
take and then press the pressure release button and turn off the
compressor while turning the hand crank at 231 meters per minute. Next,
press control, alt, delete, caps lock, shift, number lock, escape and
tab simultaneously. Press enter.
You will have ten seconds to complete the procedure. If you fail to
respond in the time limit allowed, simply purchase a new Craft-O-Matic
Adjustable Subscription Cancellation Unit and start from the beginning.
Failure to comply with the unsubscribe policy will result in immediate
termination of your subscription to the thread so please follow the above
directions closely.
How To Unsubscribe from a forum
To unsubscribe from this forum you must first purchase a Craft-O-Matic
Adjustable Subscription Cancellation Unit. The unit can be obtained from
most hardware stores and dental clinics. Be sure to obtain the proper
permits to operate the unit from the Nuclear Regulatory Commission and
the Food and Drug Administration in Washington D.C. USA.
Be sure to carefully unpack the kit and place each component in its
accompanying mesh safety bag. Mount the Pershing DF4 mesinator on top of
the perforated Gerring Mach 77 refibulator and attach them using the
eight-millimeter torque fork. Be sure that the refibulator is mounted at
a 66-degree angle and properly dispersed so that it is flush with the
curved section of the Pyrex thistle tube. Place the four sections of the
triangular separation gear into the posture cylinder and lock them into
place using the band-aid adhesive strip. Insert the wiggling pin into
the wobbling hole, making sure that it seated correctly. Place the D
cell battery and the eleven 9 volt batteries in the power chamber.
The device should be calibrated before operation using the optional
digital corkscrew accessory pack prior to operation. Insert the digital
corkscrew through the electronic combustion service chamber using
caution not to touch the reinforced tungsten igniter control module and
quickly turn the inverter drive to 28.6 degrees. Turn the Craft-O-Matic
Adjustable Subscription Cancellation Unit upside down and hit the bottom
plate with a 48-ounce ball-peen hammer while shaking the unit
vigorously. Force open the door to the incineration valve compartment
and set the pressure gauge to 719 psi. Close the door and seal it shut
with duct tape. The unit should now be properly calibrated and ready to
use.
Before activating the Craft-O-Matic Adjustable Subscription Cancellation
Unit, you must first elevate it to a height of 229 feet above sea level
to insure that the unit receives the proper oxygen level and barometric
pressure. Point the aerial to 17 degrees north by northeast to within
the parameters of the Telstar GS-2 weather satellite and apply pressure
to the wing shaft on the southern most section of the modular
accelerator. Using the special ratchet adapter supplied with the unit,
rotate the heater core to the "on" position. The "on" position has been
obtained when the green light begins to flash, signifying that the red
light is about to go off. Once the red light is off, flip the toggle
switch labeled "ON/OFF" to the "ON" position and count to 47 before
logging on to the system.
Logon using your username and password and wait for the prompt. Once
prompted you must check the box with the appropriate action you wish to
take and then press the pressure release button and turn off the
compressor while turning the hand crank at 231 meters per minute. Next,
press control, alt, delete, caps lock, shift, number lock, escape and
tab simultaneously. Press enter.
You will have ten seconds to complete the procedure. If you fail to
respond in the time limit allowed, simply purchase a new Craft-O-Matic
Adjustable Subscription Cancellation Unit and start from the beginning.
Failure to comply with the unsubscribe policy will result in immediate
termination of your subscription to the thread so please follow the above
directions closely.